3169K UV Adhesive Case Study: Component Fixing in Lithium Battery Packs
How one adhesive change cut BMS fixing time from 45 seconds to 12 seconds and vibration failures from 2.1 to 0.3 percent
The result first: a battery pack plant replaced a solvent adhesive with 3169K single component UV adhesive and cut per board fixing time from 45 seconds plus 24 hours drying to 12 seconds with immediate handling. Vibration test failures fell from 2.1 percent to 0.3 percent. The curing lamp matters for takt time, but the failure was caused by the adhesive, and the adhesive is where the engineering effort went.
What Went Wrong With the Old Adhesive
The plant bonds relay supports, shunt holders and connector blocks onto BMS boards before potting, roughly 300,000 packs a year. The solvent adhesive failed in three ways:
- It cured by evaporation, so parts could move for hours. Handled boards arrived at the potting station misaligned.
- Its solvent attacked the solder mask, leaving white halos around the bond line.
- Twenty four hours of rack drying locked up work in process and about 60 square metres of floor.
None of these was a lamp problem. Each traced back to how the adhesive cured and how it behaved on the substrate, which is why the evaluation focused on chemistry, viscosity and strength data rather than on curing hardware.
Why 3169K Was Chosen
3169K is a single component polyurethane acrylate that cures on UV or visible light exposure and needs no mixing. Four properties decided the selection.
1. Viscosity 12,000 mPa·s Fits the Dispensing Window
Too thin and the adhesive runs onto gold pads and under neighbouring parts; too thick and it bridges the component instead of wetting its edge. At 12,000 ± 1,500 mPa·s 3169K dispenses from a standard time pressure valve, stays where it is placed and flows into the 0.3-0.5mm gap along the component edge. The plant kept its existing valve and nozzle, so no capital cost was involved.
2. Shore D 80 and 13 MPa Hold Under Vibration
BMS boards face road vibration, drop testing and connector insertion force. A soft adhesive lets the component creep; a brittle one cracks at the fillet. 3169K cures to Shore D 80 with 13 MPa tensile strength, which is rigid enough to hold a relay support yet tough enough to absorb impact, and it keeps that performance through aging rather than embrittling in service.
3. Shear Strength on Aluminum and PC
The board carries an aluminum busbar and PC connector housings, two substrates that rarely share the same adhesive. Measured shear strength is more than 4 MPa on PC/PC and more than 7 MPa on PC/aluminum, so one grade covers both joints. This removed the second adhesive the plant used to keep for metal parts.
4. Electrical Safety Next to Sense Wires
Adhesive runs centimeters from live sense wires and shunts. 3169K gives 20 kV/mm dielectric strength with dielectric constant 2.4 and dielectric loss 0.03 at 1MHz, so it insulates without disturbing measurement. The cured layer is also colorless and transparent, letting inspectors confirm coverage instead of pulling parts to check.
The Curing Lamp: A Supporting Role
3169K needs light to reach the bond line, so the plant mounted a 200W 395nm UV LED lamp from the same supplier on the existing fixture at a 30-50mm working distance. Five seconds of exposure delivers about 6000 mJ/cm² at 2mm bond line thickness, which matches the 12 second takt. The lamp replaced a 4000W mercury unit on that station mainly because it starts instantly and adds no heat next to the cells; the adhesive choice is what fixed the failure mode.
| Parameter | Value |
|---|---|
| Lamp used | 200W UV LED, 395nm, 30-50mm distance |
| Exposure | 5 seconds |
| Accumulated energy | 6000 mJ/cm² at 2mm |
Results After Three Months
| Indicator | Before | After |
|---|---|---|
| Fixing cycle time | 45s plus 24h drying | 12s, handle immediately |
| Vibration failure rate | 2.1 percent | 0.3 percent |
| Solder mask defects | White marks at bond line | None observed |
| Adhesive grades in stock | Two, plastic and metal | One, 3169K |
| Floor space for racks | About 60 square metres | Released to assembly |
Three Points Worth Copying
- Diagnose the failure mode before buying hardware. Here the adhesive cured by evaporation, so no lamp upgrade could have solved it.
- Judge an adhesive by viscosity, hardness, shear strength and dielectric data on your own substrates, not by cure speed alone.
- Then match the lamp to the adhesive, and verify irradiance with a UV meter at the real working distance.
Request a Similar Evaluation
Send your substrate pair, component size, bond line thickness and takt time. Our engineers will confirm the 3169K grade and dispensing parameters, and specify the UV LED lamp only after the adhesive is settled.



